Your disposal hums but won't spin โ the impeller plate is jammed. It's completely silent when you flip the switch โ the thermal overload protector has tripped or the motor has failed. Water drips from the sink collar โ the sink mounting gasket has deteriorated. Each of these is a different diagnosis, and each has a different solution. Masters Plumbing Service's techs in Keyes, CA arrive with the jamming tools, reset wrench, and replacement units to resolve any disposal failure same visit.
๐ Call +1-855-718-1500 โ Same-Day Service
We carry replacement units on the truck in common horsepower ratings so a same-day swap is possible when the motor has genuinely failed.
A disposal that hums but won't spin almost always just needs the jam cleared with an Allen wrench at the center socket and the reset button pressed โ a 5-minute fix that doesn't require a new unit.
InSinkErator (Badger, Badger 5, Compact, Evolution series), Moen GXS/GX series, Waste King, KitchenAid, and Whirlpool disposals all mount differently and have specific jam-clearing procedures. We know the mounting assembly for each brand and carry the correct jam-clearing wrench sizes.
We give you the actual cost comparison. If clearing the jam and pressing the reset button fixes it, that's what we do. If the motor has failed, we show you the replacement options and install same-day.
A disposal installed without properly removing the dishwasher drain knockout plug is a common installation error that floods the dishwasher interior. We check this and correct it if present.
From a simple jam clear to a full replacement with drain reconnection, here's how we handle each garbage disposal scenario in Keyes, CA.
If the jam-clearing wrench won't budge the impeller, the motor shaft may be seized rather than just stuck from debris โ we distinguish between the two before recommending replacement.
If power is confirmed at the disposal and it still won't start after a reset, the motor is failed. We then move to the replacement conversation with honest cost comparison.
Disposal leaks come from three locations: the sink flange (top of the unit where it mounts to the sink drain opening โ repaired by re-sealing the flange with plumber's putty and re-tightening the mounting ring), the side port (dishwasher drain hose connection โ usually a loose hose clamp or cracked fitting), or the bottom of the unit (internal body crack or failed internal seal โ indicates replacement needed).
If the turntable bearing has failed โ indicated by a loud rumbling throughout operation rather than specific impact sounds โ that's an internal motor wear failure that warrants replacement.
If the slow drain persists after cleaning the drain arm and p-trap, a camera scope of the kitchen drain line is the next step to check for blockage further downstream.
Replacement includes: safely disconnecting electrical at the junction box under the sink, removing the old unit and mounting assembly, installing the new unit with correct wiring and plumbing connections, testing for full jam-free operation, and verifying zero leaks at all connections before leaving.
A disposal call takes 30โ60 minutes in most cases. Here's exactly how it goes โ from your first call to a clean, functional kitchen drain.
If you know the disposal is over 10 years old, tell us โ that changes how we approach the repair-vs-replace conversation upfront.
The tech identifies the failure type in minutes: jam test at the motor socket, reset button check, power confirmation at the wire connections, leak source tracing. We know what each symptom means and we go straight to confirming it.
You decide. We don't upsell replacement when repair is the right answer, and we don't push a cheap repair that won't hold on a unit that's genuinely at end of life.
After repair or replacement, we run the disposal through a full test: several cycles with water running, check under the sink for any drip at all connection points, and confirm the drain arm clears at a normal rate.

Disposal hummed and wouldn't spin. I'd already tried the Allen wrench trick without success. Masters Plumbing Service's tech came out, worked the impeller free from underneath while removing a piece of broken ceramic that had fallen in โ it had wedged between the impeller and the grinding ring in a way I couldn't have cleared from the top. Cleared the jam, pressed the reset, tested. Five-minute fix. Honest about the call minimum charge, no attempt to upsell a replacement on a perfectly good motor.
After we added a dishwasher, it started backing up every cycle. Masters Plumbing Service found the problem immediately โ the previous installer had forgotten to knock out the dishwasher drain plug inside the disposal inlet. The plug was blocking the drain port. Two-minute fix. The tech also tightened the dishwasher drain hose clamp, which was loose. Never had another backup.
Disposal leaking from the sink collar area. Previous owner had installed it with silicone instead of plumber's putty at the flange โ silicone doesn't hold the mounting pressure correctly and had separated. Tech re-seated the flange with putty, re-tightened the mounting ring, and the leak stopped. Tested with a full minute of running water. All clear.

Masters Plumbing Service dispatches garbage disposal repair and replacement technicians throughout Keyes and the broader Keyes, CA service area. Most calls are same-day โ call to check today's availability.

Call now โ same-day service available in Keyes and across Keyes, CA.
๐ Call +1-855-718-1500 Now